Fireball Dragon Stainless Steel Hardware

Not sure what length to buy? Use this Hardware Measurement Tool.

Dragon Stainless Steel Hardware is engineered to maximize durability and longevity to meet the needs of the new skateboarders to professional skateboarders and longboarders alike. Fear stripped hardware no longer.

Note that the nuts in this set are NOT stainless steel, but rather steel coated in zinc. Stainless steel bolts matched with stainless nuts is highly prone to cold welding. 

Drive Types

FLAT PHILLIPS - Classic skateboard hardware head. Sinks into the board to provide maximum fastening strength on top mounted boards. Requires a Phillips Head bit or driver. These cannot be felt under feet.

BUTTON ALLEN - Sits atop the deck or trucks, rather than countersunk like the Flat Allen and Flat Phillips. Requires a 1/8”allen bit or driver. Comes with stainless steel washers to prevent damage to deck or trucks. Works best on drop-thru decks, but still works on top mounted decks. The bolt head can be felt under feet, allowing riders to correct foot placement.

FLAT ALLEN - Uses the same head shape as the Flat Phillips, except requires a 1/8” allen bit or driver, for reduced risk of stripping. These cannot be felt under feet.

Design Inspiration

While most hardware bolts are steel with some kind of paint or coating, the bolts in this set are full stainless steel. This hardware can withstand extreme usage and beatings, along with all weather conditions. Guaranteed. 

Specifications

• Construction - Stainless steel bolts with zinc coated steel nuts
• Drive Types – Flat Phillips, Flat Allen and Button Allen
• Flat Phillips - Used for top mounted boards.
• Flat Allen- Used for top mounted boards.
• Button Allen - Used for drop-through mounted boards.
• Length - All drive heads come in lengths ranging from 1”to 3” to for customizing your setup.
• Designed specifically for skateboards

Disclaimer: Ride with caution and always wear a helmet.

Dragon Precision Spacers and Speed Rings

Dragon Precision Spacers and Speed Rings are manufactured to provide a precision fit with extremely low tolerances in-between your skateboard bearings. This allows you to crank your axle nut all the way down, which in turn reduces slop and increases the longevity, durability and performance of your bearings by great amounts.

Design Inspiration

We here at Fireball were tired of rattling coming from our bearings and spacers due to imperfections in the manufacturing process of bearings spacers. Many other spacers are manufactured with stamped steel, causing a sloppy fit. This causes the bearing to have higher tolerances and lose its roll speed over time. We’re not sure about you, but we like to make our gear last quite a while.

Specifications

• Width - 0.405”(10.29 mm)
• Axle Size - 8mm
• Precision Cut for Extremely Tight Tolerances - Between +/- 0.02 mm
• Construction - Iron with Zinc Coating for protection from rust.
• Durability - Equal to the durability of stamped steel with a more precise fitment.
• Perfect Fitment for Dragon Endure and Race Bearings - Designed and tested to work extremely well with our Dragon Bearing lineup.

Disclaimer: These Spacers and Speeds rings will cause your board to accelerate at speeds which can potentially cause combustion. Ride with caution and always wear a helmet.

 INSTALLATION:

1. Remove everything from the skateboard axle
2. Place a Dragon Speed Ring (small washer) on the axle
3. Place a bearing on the axle with the shield towards the middle of the skateboard
4. Place a Dragon Spacer on the axle
5. Place a bearing on the axle with the shield towards the middle of the skateboard
6. Push wheel down on the bearing with the outward part of the wheel facing towards the middle of the skateboard
7. Remove wheel and seated bearing from the axle
8. Flip wheel and place it back on the axle, installing the second bearing
9. Place a Dragon Speed Ring on the axle
10. Tighten axle nut down all the way (some clicking is often normal, bearing is fully seating into the wheel)
11. Repeat and go shred!

If you're looking for hardware that's practically immune to rust and stripping, you've come to the right place. The Fireball Dragon Stainless Steel Hardware set comes complete with more hardware than you'll know what to do with. Whether you're building your quiver for the first time or replacing the hardware on some of your favorite setups, this bundle has you covered. Plus, each nut and bolt are made from stainless steel to provide optimal strength and superior resistance to rust. 

Three Head Types

With Dragon Hardware, you can choose from three different head types in order to best accommodate your ride. The best practices for each head are as follows:

Flat Allen

The right choice for skateboards with flush mounting and riders looking for an allen key head for increased resistance in stripping. 

Flat Phillips

The right choice for skateboards with flush mounting and riders looking to easily use a Phillips-head screwdriver to get the job done.

Button Allen

The right choice for longboards and riders looking for a raised hardward that they can feel with their feet. Also the right choice for quick mounting on drop through boards. Similar to the flat option the allen key head provides increased resistance in stripping as well. 

Beast Guarantee

All Fireball products come with the Beast Guarantee, which promises against defects. Even if the product is worn out from normal use, Fireball will give 25% replacements under this top quality promise.

Comes Complete With:

• 8 of each size mounting hardware
• Allen Key
• Kingpin Nuts
• Axle Nuts
• Bearing Spacers and Speed Rings

Specifications

• Length: 1.0", 1.25", 1.5", 1.75", 2.0", 2.25", 2.5", 2.75", 3.0" / 2.54cm, 3.18cm, 3.81cm, 4.45cm, 5.08cm, 5.72cm, 6.35cm, 6.99cm, 7.62cm
• Grade: Stainless steel bolts with steel zinc coated nuts
• Special Features: High quality bolts with limited lifetime guarantee