Fireball Logo (3) Sticker Pack

Slap this pack of three anywhere you’d like. High quality 4-color printing with hashtag backing for contest entry. Post up this sticker and post with hashtag #RIDEFIRE to show the skate world your you're reppin'.

Specifications

• Print - High Quality 4 Color Print
• Colors - MultiSize- 3.6 x 2.0 inches (9.1 x 5 cm)

Fireball Dragon Stainless Steel Hardware

Not sure what length to buy? Use this Hardware Measurement Tool.

Dragon Stainless Steel Hardware is engineered to maximize durability and longevity to meet the needs of the new skateboarders to professional skateboarders and longboarders alike. Fear stripped hardware no longer.

Note that the nuts in this set are NOT stainless steel, but rather steel coated in zinc. Stainless steel bolts matched with stainless nuts is highly prone to cold welding. 

Drive Types

FLAT PHILLIPS - Classic skateboard hardware head. Sinks into the board to provide maximum fastening strength on top mounted boards. Requires a Phillips Head bit or driver. These cannot be felt under feet.

BUTTON ALLEN - Sits atop the deck or trucks, rather than countersunk like the Flat Allen and Flat Phillips. Requires a 1/8”allen bit or driver. Comes with stainless steel washers to prevent damage to deck or trucks. Works best on drop-thru decks, but still works on top mounted decks. The bolt head can be felt under feet, allowing riders to correct foot placement.

FLAT ALLEN - Uses the same head shape as the Flat Phillips, except requires a 1/8” allen bit or driver, for reduced risk of stripping. These cannot be felt under feet.

Design Inspiration

While most hardware bolts are steel with some kind of paint or coating, the bolts in this set are full stainless steel. This hardware can withstand extreme usage and beatings, along with all weather conditions. Guaranteed. 

Specifications

• Construction - Stainless steel bolts with zinc coated steel nuts
• Drive Types – Flat Phillips, Flat Allen and Button Allen
• Flat Phillips - Used for top mounted boards.
• Flat Allen- Used for top mounted boards.
• Button Allen - Used for drop-through mounted boards.
• Length - All drive heads come in lengths ranging from 1”to 3” to for customizing your setup.
• Designed specifically for skateboards

Disclaimer: Ride with caution and always wear a helmet.

Dragon Precision Spacers and Speed Rings

Dragon Precision Spacers and Speed Rings are manufactured to provide a precision fit with extremely low tolerances in-between your skateboard bearings. This allows you to crank your axle nut all the way down, which in turn reduces slop and increases the longevity, durability and performance of your bearings by great amounts.

Design Inspiration

We here at Fireball were tired of rattling coming from our bearings and spacers due to imperfections in the manufacturing process of bearings spacers. Many other spacers are manufactured with stamped steel, causing a sloppy fit. This causes the bearing to have higher tolerances and lose its roll speed over time. We’re not sure about you, but we like to make our gear last as long as possible.

Specifications

• Width - 0.405”(10.29 mm)
• Axle Size - 8mm
• Precision Machined for Extremely Tight Tolerances - Between +/- 0.02 mm
• Construction - Iron with Zinc Coating for protection from rust.
• Durability - Equal to the durability of stamped steel with a more precise fitment.
• Perfect Fitment for Dragon Endure and Race Bearings - Designed and tested to work extremely well with our Dragon Bearing lineup.

Disclaimer: These Spacers and Speeds rings will cause your board to

accelerate at speeds which can potentially cause combustion. Ride with caution and always wear a helmet. 

1. Remove everything from the skateboard axle
2. Place a Dragon Speed Ring (small washer) on the axle
3. Place a bearing on the axle with the shield towards the middle of the skateboard
4. Place a Dragon Spacer on the axle
5. Place a bearing on the axle with the shield towards the middle of the skateboard
6. Push wheel down on the bearing with the outward part of the wheel facing towards the middle of the skateboard
7. Remove wheel and seated bearing from the axle
8. Flip wheel and place it back on the axle, installing the second bearing
9. Place a Dragon Speed Ring on the axle
10. Tighten axle nut down all the way (some clicking is often normal, bearing is fully seating into the wheel)
11. Repeat and go shred!

Fireball Dragon Bearings for Longboards and Skateboards

Dragon Bearings are designed from the ground up for skateboarding. After over a year of testing, Dragons are fast, long lasting, and fairly priced. 

Bearing Types

ENDURE – These super durable bearings are lubricated with our signature grease formula to ensure that the weather doesn’t ruin your skate session. We have tested these bearings for countless months in the South Bay of California and they have proven to hold up in salty, ocean air, wet conditions,through sand, and held their tight tolerances through the chunder riddled roads of Malibu.

RACE – These blazingly fast bearings are lubricated with our signature oil formula to ensure that right out of the box you will have an unmatched, smooth, fast ride. We have tested these bearings at numerous races, slide jams, free ride sessions,downhill runs, park sessions, street sessions, cruising and dancing. The Races have proven to perform at their peak, even months after installation.

Design Inspiration

We wanted to create a high end bearing at a fair price. Each bearing is double sealed with extremely tight non-contact labyrinth seals to prevent dirt and gunk from hindering performance.

Pro Tip

DRAGONS do not come with speed rings and spacers. Install spacers in between your bearings to reduce slop and improve the longevity of your bearings in all applications.

Specifications

• Axle Fitment: 8mm
• ABEC Rating: None, designed specifically for action sport use
• Measurement: 22mm (diameter) x 8mm (inner diameter) x 7mm (width)
• Special Features: Two unique lubricants to match ride style and increase bearing performance.